Skip to content
Call (803) 220-0101
3625 Centre Circle, Ste C
Fort Mill, SC 29715

07News & Insights

Fog System Design Blunders, Part 2: Overlooking the Evaporative Cooling Effect

A fog humidifier cools the air as its droplets evaporate, and that effect must never be overlooked. It is usually beneficial when fogging with an air-side economizer or directly in a hot manufacturing space. On a 100% make-up air system, though, it can reach a 30°F delta T on a design winter day, so the preheat and controls must be designed around it.

GoFog, Inc. Insights Published Updated September 2026 3 min read

High-pressure plunger pump and electric motor on a white steel base with a finned-tube heat exchanger

About this series

In Part 1, we covered undersized water treatment systems. In this second part, we explain the positive and negative impacts of evaporative cooling and why it should never be overlooked.

Why is evaporative cooling sometimes an afterthought?

When designing a fog system for a hot, dry climate, no one ignores the evaporative cooling effect, because it's an integral part of the design. But in regions that are humid in summer and only need humidification in the dry winter months, it can become an afterthought. If it's unaccounted for, you may find yourself fighting the HVAC system for control.

How does evaporative cooling affect an AHU with an air-side economizer?

When adding humidity with fog inside an air handling unit (AHU) that uses an air-side economizer, the evaporative cooling effect is almost always offset automatically. The economizer increases the return air and decreases the cold outside air to hold its supply temperature.

These applications are ideal for fogging, and there is very little concern about control modifications or make-up heat. We cover this in detail in How to Humidify an Air-Side Economizer.

Why do 100% make-up air systems need extra care?

With 100% make-up air systems, there is no return air to offset the cooling, so you must pay careful attention to the evaporative cooling effect. It can be as much as a 30°F delta T on a design winter day. Knowing this allows you to:

  • Size the preheat correctly to cover the added cooling load.
  • Integrate the preheat into the HVAC sequence of operation. As demand changes and the humidifier modulates, the amount of cooling varies. The controls must let the preheat track those changes.

Without the proper control, the air can be overcooled. That raises the relative humidity to the high limit set point in the AHU or duct, which forces the humidifier to stage down and makes it impossible to reach the desired room conditions.

What about fogging directly in the space?

Fogging directly inside a room is typical for manufacturing facilities, which install atomizing nozzles near the ceiling and use the waste heat there to evaporate the fog droplets. This "in-space" approach provides other benefits too:

  • It mixes the room air by creating a downdraft.
  • It is excellent for dust suppression.
  • It provides free cooling.

For these applications, the evaporative cooling effect is almost always beneficial because of the heat generated by the manufacturing process. The savings can be large enough that facilities have been granted sizable rebates from their local utilities for choosing fog over alternative methods that consume much more energy. Incentives like these can also apply to HVAC fogging applications, not just manufacturing. Visit dsireusa.org to research incentives available in your area.

Get help with your design

We've covered a few of the many considerations in a properly engineered fog system, and what we haven't covered could fill a book. GoFog will walk you through the entire process and provide everything you need to make the correct design and selection. Contact GoFog or call (803) 220-0101.

02FAQ

Frequently asked questions

How much evaporative cooling does a fog humidifier cause?

It depends on the application. In a 100% make-up air system, the evaporative cooling effect can be as much as a 30°F delta T on a design winter day, so the preheat must be sized and controlled to offset it.

Does fogging in an AHU with an air-side economizer need extra heat?

Usually not. The economizer almost always offsets the cooling automatically by increasing return air and reducing cold outside air, so these systems need very few control modifications or make-up heat.

What happens if the preheat doesn't offset the cooling?

The air can be cooled too much, which raises the relative humidity to the high limit set point in the AHU or duct. The humidifier then stages down and cannot meet the desired room conditions.

Have a project in mind?

GoFog engineers will review your application and provide a custom design and free quote.